Garelick 74003 TANDEM FORE & AFT SEAT SLIDE TRACK HARDW Manuel d'utilisateur télécharger pdf

Assembly and Installation Instructions for

Tandem Seat Slide Models 74001, 74002, 74003

Form 12.507

ASSEMBLY INFORMATION

Read instructions thoroughly before starting assembly and

installation.

Because of the wide variety of possible installations, mounting

hardware is not supplied. Recommended fasteners should be

#14 or #16 stainless steel wood screws long enough to

penetrate approximately 3/4 to 7/8 of the thickness of the

seat substrate but not long enough to protrude through it as

they may cause injury if sat upon.

ASSEMBLY INSTRUCTIONS FOR 74001

Refer to Fig. 1

1. Remove slide rails and cross bar from packaging. Remove

1 screw from each end of the cross bar.

2. Install the cross bar between the release handles of the

slide rails by placing one rubber washer on both sides of

each handle, aligning the holes and inserting a screw to

fasten into the ends of the cross bar. Do not over tighten as

the rubber must flex to allow for movement of the cross

bar.

ASSEMBLY INSTRUCTIONS FOR 74001, 74002, 74003

Refer to Fig. 2 and Fig. 3.

1. Turn the seat upside down to expose the seat bottom; center

seat slide rails left-to-right and front-to-back. For models

74002 and 74003 determine which side is preferred for

the release handle and then set the rails approximately 4"

in from each side of the seat. Use a tape measure to assure

that the rails are parallel to each other. This is critical to the

operation of the sliding action. Mark 3 or 4 holes in each

rail, depending on model of unit being installed, onto the

seat bottom.

2. Drill 6 or 8 pilot holes, depending on model of unit being

installed, of suitable size for the screws to be used. Fasten

rails to seat bottom finger tight. Measure between the rails

front and back to assure the rails are parallel before final

tightening of the screws. Record this measurement for

later reference.

3. Set the slide adjustment to the middle setting so there is

equal upper slide extrusion extending from either end of

the lower slide extrusion. Turn the seat right side up.

4. Determine the desired location for mounting the seat. If the

surface is covered in carpeting, place a piece of cardboard

or poster board over the area and secure with tape.

Position the seat in the desired location, keeping in mind

the seat will slide approximately 3” fore and aft. Mark the

4 outside comers of the lower slide extrusions on the

cardboard. Remove the seat and turn it upside down.

(over)

Write for

a Complete

Catalog

Phone: 651-459-9795

PO Box 8, 644 2nd Street E-mail: [email protected]

St. Paul Park, Minnesota 55071 On the Web: www.garelick.com

1/02

FIG. 2

FIG. 1

1 2

Form 12.507 1

Résumé du contenu

Page 1 - Form 12.507

Assembly and Installation Instructions forTandem Seat Slide Models 74001, 74002, 74003Form 12.507ASSEMBLY INFORMATIONRead instructions thoroughly befo

Page 2

5. Make a mental note of which side of the lower slideextrusion the mounting holes are on. Release the slide lockhandle and remove the lower slide ext

Commentaires sur ces manuels

Pas de commentaire

Garelick 74003 TANDEM FORE & AFT SEAT SLIDE TRACK HARDW Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Meubles Garelick 74003 TANDEM FORE & AFT SEAT SLIDE TRACK HARDW. Garelick 74003 TANDEM FORE & AFT SEAT SLIDE TRACK HARDWARE User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Meubles Garelick 74003 TANDEM FORE & AFT SEAT SLIDE TRACK HARDW